Dyno'd the SS/SC

[USMCFieldMP]

263whp - 238wtq! Look at the straight line of Torque! He only took it to 6800, instead of 7000... but oh well.

http://i138.photobucket.com/albums/q268/USMCFieldMP/Dyno.jpg

Dyno was done at Slowmotion in Columbus. It's on a Dynopack Dyno... They take off your wheels and connect to your wheel hubs. A lot more accurate reading, I'm told.

Dyno Pull #1
Dyno Pull #2
Dyno Pull #3

My Friends Shelby GT500 also dyno'd... 480whp 465wtq... I post those videos later, too.

[bc3tech]

Very nice man! what's "Gm Stage 2.8"? :D

Pretty sweet to think that you'd probably beat the GT500 since you likely weigh less! what year was the shelby?

very nice tho, shoulda taken it that extra 200rpm! :D

[USMCFieldMP]

Haha, No... i can't beat the Shelby. I wish. Maybe after cams and pistons. He pulls about 5 or 6 on me.

Well see what kind of numbers I get after engine surgery.

[bc3tech]

Haha, No... i can't beat the Shelby. I wish. Maybe after cams and pistons. He pulls about 5 or 6 on me.

Well see what kind of numbers I get after engine surgery.
bah you musta edited your post or something, i am pretty sure it didn't say no 400+hp when i was reading it:freak:

[Blackss05]

i dynoed at 258hp 229tq with similar mods. only things i dont have that you do are "GMPP Exhaust Manifold --- XCT 2.5" Downpipe w/ Highflow Cat --- Intense Solid TransAxle Mounts"
I have 60s and te xtc H/E sittin at home along with a CM FX300 that im waiting on paul to install. Im hoping for 270 with those mods along with header and DP. Then maybe ill add the meth kit and a 2.6 and be at 300. So what are your future plans for the balt.

[bc3tech]

i dynoed at 258hp 229tq with similar mods. only things i dont have that you do are "GMPP Exhaust Manifold --- XCT 2.5" Downpipe w/ Highflow Cat --- Intense Solid TransAxle Mounts"
I have 60s and te xtc H/E sittin at home along with a CM FX300 that im waiting on paul to install. Im hoping for 270 with those mods along with header and DP. Then maybe ill add the meth kit and a 2.6 and be at 300. So what are your future plans for the balt.
those are some good mods on top of yours too, i bet he's close to 270whp for sure if he'd ride it to redline...

[Blackss05]

yeah but most dyno shops wont run til 7k. I know mine was run up til 6850 he would not go any higher. If you hit the rev limiter it actually pulls timing. so running to 6950 or even 6900 would be ok.

[USMCFieldMP]

Actually, I raced Shelby again tonight! Pretty even through 2nd... then he pulled 2.5... it was NICE! I can't wait for my next batch of mods! Then I beat him... maybe!

I've got Cams sitting on my couch right now. I'm waiting on the Valve Springs to arrive. JBP is taking their sweet time, I suppose. Also have 10.0:1 Pistons on the way from Diamond Racing. When those get installed, I am also throwing on the Dual Pass plate, maybe a Cobra Heat Exchanger, 60# injectors, porting my blower, and MAYBE GM stage 3 PCM with a 50 shot of Nitrous. I am going to have INTENSE install and tune all of those things. I saw a LT1 Camaro put down 320WHP - 285WTQ on motor alone... then with nitrous he put down 385WHP - 445WTQ! I was like DAMN! I think I might want Nitrous now.

[bc3tech]

Actually, I raced Shelby again tonight! Pretty even through 2nd... then he pulled 2.5... it was NICE! I can't wait for my next batch of mods! Then I beat him... maybe!

I've got Cams sitting on my couch right now. I'm waiting on the Valve Springs to arrive. JBP is taking their sweet time, I suppose. Also have 10.0:1 Pistons on the way from Diamond Racing. When those get installed, I am also throwing on the Dual Pass plate, maybe a Cobra Heat Exchanger, 60# injectors, porting my blower, and MAYBE GM stage 3 PCM with a 50 shot of Nitrous. I am going to have INTENSE install and tune all of those things. I saw a LT1 Camaro put down 320WHP - 285WTQ on motor alone... then with nitrous he put down 385WHP - 445WTQ! I was like DAMN! I think I might want Nitrous now.yeah n2o = mad tq... sounds like you've got quite the laundry list. honestly i wouldn't bother porting the blower, tho. if it's going to cost you anything, that is.

[Doc]

I get 262hp and 261ft/lbs outta my 2.5 and 60's :lol: and I'm pleased....I'll break the motor open in a few weeks and 400/350 will be my goal.